This is a log of the steps I took to paint my second set of miniatures. The end-result looks like this:

Photo of the final result


Steps

Step 1 - Assembly & gun barrels

Fully assembled 3 out of 10 miniatures according to instructions booklet.

Assembled three of the minis

Drilled holes in gun barrels using a heated needle for the initial hole, then a hand drill with the smallest drill size to drill the actual hole. Unfortunately, none of the holes was actually correctly centered with the barrel.

The drilled barrel hole. Not very precise, I know

Step 2 - Basing

Based the miniatures with cat litter for the larger stones, surrounded by a superglue and baking soda mix (the baking soda acts as a catalyst, instantly hardening the glue).

The base

And the base again, but up close

Step 3 - Priming

Primed the miniatures with two layers of Abaddon Black, including the base. The base required extra attention in order to get the black into all of the cracks and crevaces.

Nothing too exciting, some black minis

Step 4 - Armor Base Coat

Applied two thin coats of Macragge Blue on all of the armor pieces. Wasn't too careful with not getting this over the black areas (pouch, weapon, under-armor etc.), since I can fix this later on.

Step 5 - Base paint & wash

Applied one thin coat of Mornfang Brown on the base. Some of it got on the armor and rim of the base, since I used a large brush, but that can be corrected later.

Then, when the paint was almost dried (after 3-4 minutes of applying it, when most of the paint was dried and matte, except a few spots where it still looked shiny and wet), applied one coat of Nuln Oil, directly from the pot. The wash dissolved and mixed with some of the still-wet brown.

While wet, the base looked like this:

Perhaps I should have waited longer

Step 6 - Base dry-brush

After the base was completely dry, I dry-brushed the base using Eshin Gray.

Looking better

Step 7 - Armor clean-up

Cleaned up the armor using a single layer of Macragge Blue. Wasn't very concerned with the soles of the feet, which can stay dirty. Got a couple of spots of blue on the terrain, which I fixed using Mornfang Brown.

Step 8 - Armor wash

Applied a wash of Nuln Oil all over the model, while avoiding getting any more on the base.

Step 9 - Armor dry-brush

Applied a dry-brush of Calgar Blue all over the armor.

Step 10 - Gold details

Painted the gold details (chest decoration, shoulderpad rim, sword handle) with two layers of Liberator Gold (without thinning the paint as much as usual).

Corrected any mistakes using Macragge Blue (though there weren't many, since I tried to apply the gold carefully) in a single layer.

Shiny

Step 11 - Skin

Base-coated the skin areas using two layers of Mornfang Brown, while avoiding the hair, head implants and armor around the neck.

Added a single layer of Rakarth Flesh, which is very pale. Then, with the paint still wet, got some Mornfang Brown on the brush, dipped in in water, wiped it once against a paper towel, then applied it to areas that I wanted to be more shadowed or less pale (such as around the implants). Applying the paint felt like a mix between a wash and wet blending.

I was probably the most pleased with how the skin turned out

In addition to the skin, I used Rakarth Flesh to paint the sigils and eye sockets of the helmets.

Step 12 - Black details

Applied a coat of black for various elements, such as the base edge, weapons, under-armor joints, hair, grenades, joins of the grav-chutes and all of the belts and pouches.

Step 13 - Silver details

Painted silver details using Leadbelcher: parts of the rifles, swords, grenades, details on the masks, skin implants and joints of the grav-chutes. Edge-highlighted pouches and under-armor joints, without being too clean about following the edges since a dark wash will go over it.

Step 14 - Nuln oil wash

Applied Nuln Oil over all of the silver details, as well as the ribbon.

Step 15 - White details

Applied a layer of Ulthuan Gray on certain details such as the sword edge, highlights on grenades and the rifles, as well as the skull masks.

Step 16 - Red details

Applied a layer of Mephiston Red on the wax and eye sockets.